Heating Repair in Aurora, IL
When the heat stops coming on, the first sign is usually silence: the thermostat clicks, the blower runs, and the air never warms. In an Aurora January that stops being a comfort problem fast - an unheated house loses temperature overnight, and the pipes in exterior walls are the first thing to suffer. We diagnose residential heating systems in Aurora and explain what failed before any repair starts. Call (630) 467-6249.
Why Choose Us for Heating Repair in Aurora
We diagnose before we quote
A no-heat call is a question, not a parts order. We test ignition, flame sensing, airflow, pressure switches and gas pressure, then tell you which reading failed. You hear the finding before anyone reaches for a part.
Repair first, replacement last
Plenty of furnaces are condemned on age alone. We look at the failed component, the condition of the heat exchanger, and what a repair actually buys you in years, then let you decide with the numbers in front of you.
Straight answers about safety
If we find a cracked heat exchanger, a blocked flue or a rollout switch that has tripped, we say so plainly and explain what has to happen next. We do not soften a carbon monoxide finding to keep a repair small.
One point of contact
The person who diagnoses your furnace explains the repair and is the person you call if a question comes up afterward. No handoff to a call centre and no scripted upsell at the door.
HEATING SERVICE IN AURORA
Why Now: What a Cold Snap Does to an Aurora House
Aurora sits in IECC climate zone 5A, and the January normal low at Chicago Aurora Municipal Airport is 12.6 F (NOAA 1981-2010 normals, Illinois State Water Survey). Most occupied homes here – 83.7% – heat with utility gas (ACS 2024, table B25040), so a no-heat call in this city usually means a gas furnace fault rather than a boiler or a heat pump. The same failure in January is a plumbing risk: an unheated house cools through the night, and the pipes most exposed are the ones in exterior walls and unheated crawlspaces. Waiting also changes the repair, because a part that fails cleanly is simpler to replace than a heat exchanger damaged by repeated overheating.
No heat at all
The thermostat calls and the furnace stays silent. Ignition, a pressure switch or a gas valve that is not opening are the usual suspects.
- Igniter never glows
- No click at the gas valve
- Pressure switch not proving
- Breaker tripped
Furnace starts, then stops
The burners light and shut down seconds later. Flame sensing or a restricted flue is the usual cause, and the board locks out after a few tries.
- Flame sensor dirty
- Short flame then lockout
- Exhaust restricted
- Repeated retries
Blower runs, air is cold
The fan moves air but the burner never lights. The furnace is in lockout, or the thermostat is running the fan on its own.
- Fan set to ON
- Ignition lockout
- Gas supply off
- Control board fault
Heat runs, house stays cold
The furnace is working but the rooms are not. Airflow, duct leaks or a slowing blower are more likely than the burner.
- Clogged filter
- Leaking duct run
- Weak blower
- Damper closed
Furnace cycles on the limit
The burner runs until the limit switch trips, then restarts. Restricted airflow is the most common reason, and repeated trips damage the heat exchanger.
- Dirty filter
- Blocked return
- Overfiring burner
- Weak limit switch
Thermostat says heat, nothing happens
The display is on but the furnace never receives the call. Control wiring, a C-wire fault or a failed thermostat are the likely causes.
- No 24V at R
- Loose C-wire
- Zone panel fault
- Thermostat dead
Proof: What Heating Repair Covers in an Aurora Home
Ignition and Flame Sensing
What ignition failure looks like
Most no-heat calls in Aurora end at the ignition sequence. The thermostat asks for heat, the inducer starts, the pressure switch proves, and the hot surface igniter should glow and light the burners within seconds. If the igniter stays dark, the part or its circuit has failed. If the burners light and then go out, the flame sensor is not proving flame - a rod coated with oxide reads a weak microamp signal, and the board closes the gas valve to protect the house. A cracked igniter, a loose ground, a dirty sensor and a board that no longer sends voltage all look identical from the hallway. Testing the sequence in order is what separates a ten-minute sensor cleaning from a control board replacement.
Why it matters
A furnace that locks out has not failed until the sequence is tested. Replacing a board before checking the igniter and sensor is how a simple repair becomes an expensive one.
What it helps you decide
If the sensor is dirty, cleaning and a flame test settle it. If the igniter is cracked, replacement restores ignition. If the board is dead, you know that before you authorise a part.
Do this now
If the furnace clicks but never lights, stop resetting it and call (630) 467-6249. Repeated lockouts can leave unburned gas in the combustion chamber.
Inducer Motor and Pressure Switch
How a blocked flue stops the furnace
Before a gas furnace is allowed to light, it proves that exhaust can leave the house. The inducer motor pulls air through the heat exchanger, and the pressure switch closes only when it senses that draft. A nest in the vent, a sagging flue pipe, a cracked collector box or a weak inducer wheel all keep that switch open, and the board refuses to open the gas valve. Homeowners often hear the motor run and assume it is fine; a spinning wheel with a loaded or broken fin moves far less air than the switch expects. In Aurora, vent terminations that ice over during a cold snap are a common winter call. The repair is usually the blockage or the inducer, not the board.
Why it matters
A pressure switch that never proves is a safety decision, not a fault to bypass. Jumpering it to get heat back is how flue gases end up inside the house.
What it helps you decide
Clearing a vent is a different job from replacing an inducer. Measuring draft and switch state tells you which one you are paying for before any part is ordered.
Do this now
If you hear the inducer run and the burners never light, call (630) 467-6249 rather than resetting the furnace again.
Limit Switches and Overheating
Why a furnace overheats and shuts itself down
A furnace that runs for a few minutes and then stops is usually tripping its high-limit switch. The limit is a thermostat on the heat exchanger that opens when the air leaving the furnace gets too hot, and it exists because an overheating heat exchanger can crack. Restricted airflow is the usual cause: a filter that has not been changed, a return grille covered by furniture, a collapsed flex duct, or a blower that is slowing down. An overfiring burner or gas pressure set too high produces the same symptom from the other side. Because the furnace restarts after it cools, the fault is easy to live with and easy to ignore - until the limit fails closed or the heat exchanger takes the damage.
Why it matters
A limit trip is the furnace saying it is running hotter than it was designed to. Ignoring it shortens the life of the part that is most expensive to replace.
What it helps you decide
Static pressure and temperature rise readings show whether the problem is airflow or gas. That reading decides whether you need a filter, a duct repair or a burner adjustment.
Do this now
Change the filter and clear the returns first, then call (630) 467-6249 if the furnace still cycles on the limit.
Heat Exchanger and Carbon Monoxide
What a cracked heat exchanger changes
The heat exchanger is the metal that separates combustion from the air your house breathes. Cracks and holes develop from repeated heating and cooling, and a furnace that has been overheated or run with a blocked flue is more likely to develop them. A cracked exchanger can let flue gases into the supply air, which is why a carbon monoxide alarm is a leave-the-building event and not a service call to schedule. Visual inspection reaches only part of the exchanger; a combustion analyser reading and a careful look at the burner flames tell you more. If the exchanger has failed, the honest answer is that the furnace should not run, and the conversation moves to replacement rather than another repair.
Why it matters
Carbon monoxide is colourless and the early symptoms look like flu. Any crack that lets exhaust into the air stream is a health issue before it is a comfort issue.
What it helps you decide
A failed exchanger ends the repair conversation. A clean analyser reading and an intact exchanger let you repair the ignition or airflow fault with confidence.
Do this now
If a carbon monoxide alarm sounds, leave the building and call emergency services first. Do not reset the furnace. Call us once the building is clear.
The Scenario Most Aurora Homeowners Don't Plan For
Here is the call that catches people out in February. The furnace ran all winter without a problem, the thermostat still shows heat, and then one morning the burners will not stay lit. Nothing was serviced wrong and nothing obviously broke. The vent termination outside – the two plastic pipes on a high-efficiency furnace – has iced over, or the condensate line that drains the furnace has frozen and the pressure switch will not prove. A frozen drain is also why a furnace can run perfectly for weeks and then fail on the one night the temperature drops below zero.
High-efficiency furnaces condense water as they extract heat, and that water leaves through a small drain. When the drain freezes, water backs up into the collector box and the furnace locks out to protect itself. When the intake or exhaust ices at the wall, the furnace cannot prove draft. Both failures look exactly like a failed control board from the thermostat, and both are weather-driven rather than age-driven.
The fix is rarely a major part. It is a thaw, a re-routed drain, a vent termination corrected for the prevailing wind, or a condensate trap cleared. What makes it worth knowing is the timing: the first hard freeze is when these calls cluster, and a furnace that is otherwise healthy gets replaced because nobody checked the drain.
If your furnace quits on the coldest morning of the year and the thermostat is still calling, look at the outside pipes and the little drain before you assume the furnace is finished. Then call (630) 467-6249 and describe what you see. That detail shortens the visit.
REPAIR OR REPLACE
A Furnace Decision You Can Defend Later
A furnace that has failed is a decision, not just a repair. Age matters, but it is not the whole answer. What matters more is the condition of the heat exchanger, how many repairs the furnace has needed in the last few winters, whether the parts are still available, and how long you intend to stay in the house. A twelve-year-old furnace with a failed igniter is a repair. A twenty-two-year-old furnace with a cracked exchanger is not. Most calls sit somewhere between those two, which is why the readings come before the recommendation.
What waiting changes
A furnace that trips its limit all winter does not fail at a convenient time. Repeated overheating is what turns a small repair into a heat exchanger.
Age and parts
After 15 to 20 years, parts get scarce and a repair buys less time. Before that, the failed component usually tells the story.
Repair history
Three repairs in two winters is a pattern. One repair in ten years is not, and the furnace may have plenty of life left.
Heat exchanger condition
This is the deciding factor. An intact exchanger supports a repair; a failed one ends the discussion.
Comfort complaints
Cold rooms, dry air and uneven heat often come from ducts and airflow rather than the furnace itself, and a new furnace will not fix a duct problem.
Efficiency expectations
A modern furnace can use less gas, but the saving depends on the house, the ductwork and how the system is set up, not on the rating alone.
How Heating Repair Works, Step by Step
No two no-heat calls are the same, but the sequence is. Here is what happens from the first call to the moment the furnace runs again.
HOW WE WORK
You Will Know What Failed Before We Repair It
Heating repair goes wrong when the conversation starts with a part and ends with a bill. Ours starts with the reading that failed. You get the finding in plain language, the options that follow from it, and the limits of what a repair can promise. If the honest answer is that the furnace should not be repaired, you hear that too.
Findings first
The diagnostic sequence comes before any part recommendation, and normal readings are reported as normal.
Scope explained
If the repair changes once the furnace is open, we stop and explain before continuing.
Parts explained
You hear what the part does and why the old one failed, not just its name.
Clean work area
Furnace closets, floors and work surfaces are left as we found them.
What Sets Us Apart on a Heating Call
On a heating call, the difference is usually not the truck or the brand on the door. It is whether the technician tests the whole sequence before quoting a part, and whether the explanation you get matches the readings. We work the sequence in order: call for heat, inducer, pressure switch, ignition, flame sensing, gas pressure, temperature rise. When a reading is normal we say so. When it is not, you see the number. That is what makes a second opinion useful rather than confusing.
WHAT A PROPER REPAIR LEAVES YOU WITH
More Than a Furnace That Lights Again
A repair is finished when the furnace completes a full heating cycle, the temperature rise is back inside the range on the data plate, and the vent and drain are clear. Here is what that looks like in practice.
A verified ignition cycle
Burners light, flame proves, the blower starts and the furnace runs to temperature without tripping.
Correct temperature rise
Measured at the return and supply, inside the range printed on the data plate.
Clear vent and drain
Exhaust path and condensate checked, especially on high-efficiency units.
Airflow confirmed
Filter, blower and returns checked so the limit switch is not asked to compensate.
Safety switches tested
Limit and rollout switches confirmed, not bypassed.
A plain explanation
What failed, what was replaced, and what to watch for next season.
Need Help With a No-Heat Call?
If the furnace is out and the house is cooling, call and describe what it is doing. We will tell you what the symptom points to and arrange a visit. If a carbon monoxide alarm is sounding, leave the building and call emergency services first.
Heating Repair Across Aurora and the Fox Valley
Service area: Aurora, North Aurora, Montgomery, Naperville, Oswego, Batavia, Sugar Grove, Geneva and Warrenville. We also cover Elburn, St. Charles, Lisle, Winfield, West Chicago, Carol Stream, Wheaton, Downers Grove, Bolingbrook, Plainfield, Yorkville and Joliet.
The housing stock changes what a heating call looks like. Older homes near downtown Aurora and North Aurora often have ductwork that was added later, so airflow problems show up as cold rooms before the furnace fails. Newer subdivisions on the west side tend to have high-efficiency furnaces with condensate drains and PVC venting, which is where frozen drains and iced terminations appear. HVAC Repair Aurora works out of 2847 Stonebridge Ct, and knowing which of those housing types you live in shortens the diagnostic.
Frequently Asked Questions
It is a repair-versus-replace shortcut, not a price. Multiply the age of the equipment by the cost of the repair. If the result passes the threshold the rule is named for, replacement usually deserves the conversation; below it, a repair is often the better use of the money. The rule is a starting point, though. Heat exchanger condition, parts availability and how long you plan to stay in the house matter more than the arithmetic.
Ignition is the most common: a failed hot surface igniter, a flame sensor that no longer proves flame, or a pressure switch that will not close because the vent or inducer is restricted. Airflow faults come next - a clogged filter or blocked return that trips the limit switch. Less often it is the gas valve, the control board or the thermostat circuit. The symptom usually narrows it before the furnace is opened.
It depends on which part failed, and the range is wide. A flame sensor cleaning, an igniter or a pressure switch is a small repair. A gas valve, inducer motor or control board is a larger one. A failed heat exchanger is not a repair at all. We test the sequence first, tell you which of those you are facing, and you decide before any work starts.
A blown fuse usually means the furnace is completely dead: no display, no inducer, no click at the thermostat. The fuse sits on the control board and protects the board from a short. Replacing it without finding the short usually blows the next one. If the fuse has failed more than once, stop and have the low-voltage circuit tested.
Some things are safe: changing the filter, checking the breaker, confirming the thermostat is set to heat. Anything inside the burner compartment is not. Gas pressure, ignition, flame sensing and the heat exchanger all need instruments and a sequence test, and a mistake can leave unburned gas or carbon monoxide in the house. If the furnace clicks but will not light, that is the point to call (630) 467-6249.
Most gas furnaces are expected to run 15 to 20 years with regular filter changes and occasional repairs. A furnace near the end of that range can still be worth repairing if the heat exchanger is sound, but parts availability and the cost of the next failure matter. Age alone is not a reason to replace; a failed heat exchanger is.