Furnace Repair in Aurora, IL

A furnace usually gives one clear sign before it quits: a click with no flame, a blower that runs with cold air, or a heat cycle that stops after a minute and starts again. What it does not give is an explanation, and the same symptom can come from an igniter, a pressure switch, a blocked filter or a control board. We repair gas furnaces in Aurora by testing the sequence in order - call for heat, inducer, proof of draft, ignition, proof of flame, blower - and replacing the part that actually failed rather than the one that is easiest to reach. Call (630) 467-6249.

Why Choose Us for Furnace Repair in Aurora

The sequence is tested in order

A furnace asks for heat in steps, and each step has to prove itself before the next one happens. Testing in that order tells you whether the fault is ignition, draft, flame sensing or airflow in minutes, instead of swapping parts until the symptom changes.

Flame sensing is measured, not guessed

A flame sensor that reads low microamps will light the burner and then drop it out a few seconds later, which looks exactly like a gas valve or a board failure. We measure the signal and clean or replace the sensor before anything more expensive is considered.

The heat exchanger is inspected, not assumed

A cracked heat exchanger is a carbon monoxide problem, not a repair. It is checked on every furnace call where the age or the symptoms warrant it, and you hear the finding in plain language with the risk attached.

Repair or replace, decided on age and condition

Most gas furnaces are expected to run 15 to 20 years. Past that, a blower motor or a control board can cost more than the remaining life of the cabinet, and we say so rather than repairing a furnace that is about to fail again.

FURNACE REPAIR IN AURORA

Why Now: What a Cold Snap Does to a Furnace

The January normal low at Chicago Aurora Municipal Airport is 12.6 F (NOAA 1981-2010 normals, Illinois State Water Survey), and a furnace that runs continuously for days is a different machine from one that cycles on a mild afternoon. Cold snaps expose weak igniters, tired inducer motors and pressure switches that were only just closing. On high-efficiency furnaces the vent termination and the condensate line are the usual casualties: a blocked or iced termination stops the pressure switch proving draft, and the furnace locks out with no flame at all.

Waiting makes the repair worse in two ways. A furnace short-cycling on a dirty filter or a restricted return runs hot, and heat is what kills blower motors and warps limits. And a furnace that has been locked out for days in freezing weather puts the plumbing at risk, because a house that loses heat in an Aurora January can freeze pipes in a single night. The earlier the fault is found, the smaller the repair usually is.

No heat, and the furnace is silent

No inducer sound and no click at the thermostat points to power, a fuse on the control board, a door switch or the thermostat circuit before it points to gas.

Clicking but no flame

The igniter glows or the spark clicks and nothing lights. That is usually gas supply, a failed igniter, a dirty flame sensor or a pressure switch that never proved draft.

Starts, then stops after a minute

A cycle that begins normally and shuts down early is the classic signature of a flame sensor reading low, a pressure switch opening, or a limit switch tripping on heat.

Short cycling

The furnace reaches temperature, shuts off, and comes back within minutes. Restricted airflow, an oversized furnace or a thermostat in a bad location all do this.

Cold air from the vents

The blower runs but the air is cool. Either the burner never lit, or the furnace is in fan-only mode because the thermostat is set to on rather than auto.

Noise, smell or a carbon monoxide alarm

Rumbling, a screeching inducer, soot, a gas smell or a CO alarm are stop-and-call symptoms, not things to watch for another week.

Proof: What Furnace Repair Covers in an Aurora Home

Hot Surface Igniter, Flame Sensor and Spark

Why a furnace clicks but does not light

A modern gas furnace lights in a fixed order. The thermostat calls for heat, the inducer motor starts, a pressure switch proves the draft, and only then does the ignition system energise: a silicon nitride or carbide hot surface igniter glows, or a spark electrode arcs, and the gas valve opens. Once flame is established, a flame sensor in the burner path proves it by passing a small current, and the board keeps the gas valve open only while that signal is present. An igniter that no longer glows, a sensor coated in oxide, or a gas valve that does not open all produce the same complaint - no heat - and each one is a different repair. Testing the igniter for resistance and the sensor for microamps separates them without replacing either.

Why it matters

Parts swapped by guesswork cost more than the diagnosis, and the real fault stays in place.

What it helps you decide

It tells you whether the failure is ignition, gas supply or flame proving, which is the difference between a small part and a valve.

Do this now

If you smell gas, leave the house and call the utility before anything else.

Pressure Switches, Inducers and Venting

Why a furnace starts and then stops

The inducer is a small blower that pulls combustion gases through the heat exchanger and pushes them outside, and a pressure switch confirms that draft before the board allows ignition. If the vent is blocked, the termination is iced over, the condensate trap is full, or the inducer is failing, the switch never closes and the furnace locks out without ever trying to light. On high-efficiency furnaces the same switch can open mid-cycle when water collects in a sagging vent pipe. The error code usually points at the switch, which is why the switch is often replaced when the real fault is the venting or the drain. The venting route, its slope and the termination are inspected before the switch is condemned, because a switch that closes on a bench proves nothing about a blocked flue.

Why it matters

A pressure switch replaced without checking the vent fails again the next cold night.

What it helps you decide

It separates a failed switch from a blocked flue, a frozen termination or a water trap that needs draining.

Do this now

Note the flashing code on the board before you call; it narrows the fault fast.

Airflow: Filters, Limits and the Blower

Why a furnace overheats and shuts down

A furnace is designed to move a specific amount of air across the heat exchanger, and when it cannot, the limit switch opens on temperature and shuts the burner down while the blower keeps running. The usual cause is a filter that has not been changed, a return blocked by furniture or a closed register, a dirty evaporator coil, or a blower wheel loaded with dust. Less often the blower motor itself is failing, or the speed tap is wrong after a board replacement. Measuring temperature rise across the furnace and static pressure in the ductwork answers the question that a visual inspection cannot: is this a part, or is the system starving for air. That is why the filter and the ductwork are part of a furnace repair, not an upsell.

Why it matters

Short cycling on a limit switch is how blower motors and heat exchangers are destroyed.

What it helps you decide

It shows whether the fix is a filter, a duct correction or a blower repair, and whether the furnace is oversized for the ductwork.

Do this now

Change the filter before the visit so the reading reflects the system, not the filter.

Gas Valve, Control Board and Heat Exchanger

What is left when ignition and airflow are ruled out

When the furnace proves draft, lights, senses flame and still fails, the remaining suspects are the gas valve, the control board and the heat exchanger. A gas valve can fail to open, open weakly or fail to modulate, and manifold pressure is measured rather than assumed. A control board can lose a relay, misread a sensor or stop sending voltage to the inducer. The heat exchanger is the serious one: cracks or holes in the primary or secondary section let combustion products into the supply air, and that is a carbon monoxide risk rather than a performance problem. It is inspected visually and with combustion analysis where the age or symptoms call for it. A combustion test on the flue gas tells you what the eye cannot, and it is how a marginal exchanger is confirmed.

Why it matters

A failed heat exchanger ends the repair conversation, and a gas valve or board is the point where replacement often makes more sense.

What it helps you decide

It tells you whether this furnace is worth repairing at its age, and whether the flue gas is safe.

Do this now

If a CO alarm sounds, leave the house and call emergency services before calling us.

The Scenario That Looks Like a Dead Board

Here is the call that arrives on the coldest night of the year. The furnace ran all evening, then locked out. The board flashes a pressure switch code, the inducer runs, and nothing lights. The obvious conclusion is a failed pressure switch, and on a different day it might be. On this night the cause is outside: the high-efficiency vent termination has iced over, the inducer cannot move air against the blockage, and the switch is doing exactly what it was designed to do by refusing to prove draft.

Replacing the switch would produce heat for an hour and then the same lockout. The repair is at the termination: clear the ice, check the slope and the support of the vent run, confirm the condensate trap is not full, and look at whether the termination is sited where snow and dripping water collect. Aurora winters put a lot of furnaces in that position, especially where the vent exits at a height that a roof edge drips onto. The same pattern shows up with a sagging vent pipe holding water or a condensate line that has frozen solid.

That is why the diagnosis starts at the sequence rather than at the error code. If your furnace locks out on cold nights and restarts by itself in the morning, describe the vent and the termination when you call (630) 467-6249. The pattern is the clue.

furnace repair Aurora

REPAIR OR REPLACE

A Furnace Decision Based on Condition, Not on Age Alone

Furnace age matters, but condition decides. Most gas furnaces are expected to run 15 to 20 years, and a furnace at twelve with a failed igniter is a straightforward repair. The same furnace at twenty with a cracked heat exchanger is finished regardless of what the part costs. We look at the heat exchanger, the inducer, the blower and the cabinet before we recommend anything, and we tell you when a repair is buying months rather than years.

The framework we use

Under ten years with one failed component: repair. Ten to fifteen years: weigh the part against the condition of the heat exchanger and blower. Over fifteen years with a major failure: replace. At twenty-five years, replace whatever the fault is.

Under ten years

An igniter, flame sensor, pressure switch or blower capacitor is worth replacing. The cabinet has most of its service life left.

Ten to fifteen years

The deciding questions are the heat exchanger and the inducer. If either is failing, a repair buys a season rather than years.

Over fifteen years with a major part

A gas valve, control board or blower motor on a cabinet this old is usually money spent on a furnace that is close to the end of its service life.

A failed heat exchanger

Replace it. A cracked or perforated exchanger is a carbon monoxide risk, and it is not a part that gets patched.

Twenty-five years or more

Replace regardless of the fault. Parts availability, efficiency and the condition of the ductwork all argue the same way.

HOW WE WORK

You Will Know Which Part Failed Before It Is Replaced

Furnace repair goes wrong when an error code is treated as a diagnosis. A pressure switch code can mean a switch, a blocked vent or a frozen condensate line, and a flame-sensing fault can mean a sensor, a ground or a board. Ours starts with the sequence and the readings, and you hear what was found before anything is ordered.

Readings reported

Flame signal, pressure and temperature rise are discussed, not just the part name.

Safety first

Gas leaks, CO alarms and heat exchanger faults stop the visit until they are resolved.

Scope explained

If the repair changes once the furnace is open, we stop and explain before continuing.

Work area left clean

The cabinet is closed, the filter replaced and the area left as we found it.

What Sets Us Apart on a Furnace Call

On a furnace call the difference is rarely the van or the brand of part. It is whether anyone watched the sequence run and measured the flame signal, or whether the board’s code was treated as the answer. We test in order, measure what the furnace is actually doing, and put the reading next to the age and condition of the cabinet. That is why some of our calls end with a sensor cleaning and others end with an honest conversation about replacement.

Technician adjusting the control panel of a wall-mounted heating unit

WHAT A PROPER REPAIR LEAVES YOU WITH

More Than Heat Coming Back

A furnace repair is finished when the unit runs full cycles, the readings are in range and the safety devices have been proved. Here is what that looks like in practice.

A full heat cycle

The furnace lights, proves flame, runs to temperature and shuts down cleanly, more than once.

Readings in range

Flame signal, manifold pressure, temperature rise and static pressure checked against the data plate.

Safety devices proved

Pressure switch, limit and rollout switch confirmed working, not bypassed.

Heat exchanger checked

Inspected where the age or symptoms warrant it, with the finding reported.

Filter and airflow addressed

A loaded filter replaced and any obvious return restriction pointed out.

A plain explanation

What failed, why it failed, and what the condition of the rest of the furnace means for the next few winters.

No Heat, or a Furnace That Keeps Locking Out?

If the furnace will not light, keeps stopping early, or is flashing a code, call and describe what it does. We will tell you what the symptom points to and arrange a visit. If you smell gas or a carbon monoxide alarm sounds, leave the house and call emergency services first.

Furnace Repair Across Aurora and the Fox Valley

Service area: Aurora, Naperville, North Aurora, Montgomery, Oswego, Batavia, Geneva, Sugar Grove, Elburn, St. Charles, Warrenville, Lisle, Plainfield, Joliet, Bolingbrook, Downers Grove, Wheaton, Carol Stream, West Chicago, Winfield and Yorkville.

The housing stock changes what a furnace call looks like. Older homes near downtown Aurora and North Aurora often have an atmospheric furnace on a shared chimney, where draft and spillage are part of the diagnosis. Newer subdivisions on the west side tend to have high-efficiency furnaces with PVC venting and condensate traps, where icing, drain problems and pressure switch faults are more common than gas valve failures. HVAC Repair Aurora works out of 2847 Stonebridge Ct, and knowing which of those you live in decides where the test starts.

furnace maintenance Aurora

Talk to a Furnace Technician in Aurora

Frequently Asked Questions

It is a repair-versus-replace shortcut, not a price. Multiply the age of the equipment by the cost of the repair. If the result passes the threshold the rule is named for, replacement usually deserves the conversation; below it, a repair is often the better use of the money. Heat exchanger condition, parts availability and how long you plan to stay in the house matter more than the arithmetic.

Ignition and flame proving account for most no-heat calls: a failed hot surface igniter, a flame sensor coated in oxide, or a pressure switch that will not close because the vent or the inducer is restricted. Airflow faults come next, usually a loaded filter or a blocked return tripping the limit switch. Gas valve, control board and inducer motor failures are less common and more expensive.

Most gas furnaces are expected to run 15 to 20 years with regular filter changes and occasional repairs. A furnace near the top of that range can still be sound, but parts availability and the condition of the heat exchanger matter more than the number. A furnace that has had several repairs in the last few winters is telling you something the age alone does not.

A failed heat exchanger is the one that is not worth fixing, because replacing it approaches the cost of a new furnace and the cabinet is usually old by then. After that, the control board, the inducer motor and the gas valve are the larger repairs, and the blower motor sits just below them. Igniters, flame sensors and pressure switches are the small ones, which is why the sequence test matters.

Yes, in almost every case. At 25 years the furnace is past its expected service life, parts get harder to find, and the heat exchanger has had a long time to crack. A repair can still be done to get through a cold snap, but it is money spent on borrowed time. The exception is a furnace that has been serviced every year and is in genuinely good condition, which is rare at that age.

Once a year, before the heating season, is the standard for a gas furnace. A service visit checks the burners, the ignition system, the flame sensor, the inducer, the venting, the condensate trap, the filter and the heat exchanger, and it catches the failures that would otherwise appear on the coldest night. Filters still need changing between visits, usually every one to three months depending on the household.